Re: Unable to pair bluetooth soundbar (JBL SB400)
Just noticed my surface pro 2 and my cell phone wouldn't connect to it either. Tried a manuall pairing -> no result Took out and in the power of the soundbar - > problem fixed :-)
View ArticleRe: USB-power stays on when device is off
Hi again Crusey83, Just did some more checking on the Haswell NUCs. It appears that you should enable Deep S4/S5 on the Power menu to make sure that USB devices are not powered at all when the NUC is...
View ArticleEdison Yocto complete image
I just got my Edison and started the flashing process to get the latest build installed following the instructions given on Edison Getting Started Guide - Windows | Intel Communities. I just realized...
View ArticleRe: NUC - BIOS System Time error
I am not from Intel, but I believe you are describing the Linux behavior which by default changes the CMOS RTC to store UTC time instead of local time.Either you can change your wakeup time (and...
View ArticleRe: Laptop sleep/idle issues
Hi Totallycool24, can you try to tweak the power management option found in your i218-lm network adapter on device manager. uncheck the "allow the computer the turn off this device to save power". hope...
View ArticleRe: Problems compiling libnfc on Edison (libusb)
Hi, Thanks for the suggestion. It turns out that the issue with lsusb not working was due to the fact that the Edison was not in USB OTG mode. When rebooting in USB OTG mode with a USB hub attached,...
View Articlehow to delete intel account?
Hi how to delete intel account? i want to delete my account
View ArticleRe: Connecting Edison to WIFI
It looks like I'm on version 56: "edison-weekly_build_56_2014-08-20_15-54-05" How do I upgrade?
View Articleparameters for PROSETDX.msi
Hi All, I would like to do silent installation of Intel network adapter drivers in the network for some users; i have created .msi file but it is not working for me.Is there anyone who can help me to...
View ArticleClik here to view.
Re: Connecting Edison to WIFI
Getting Started has the flashing instructions for Windows, Mac and Linux.
View ArticleRe: USING A GY80 IMU WITH THE EDISON ARDUINO BOARD
SPI didn't work for me at first, until someone pointed out that the Robot_Control library had its own version of SPI.h, mucking things up. I deleted the Robot_Control file and all was well. What kind...
View ArticleIntell i7 5930k
Hi everybody, i recently ordered my new setup after my old one died on me. But stumbled up on a question. My processor is a intel i7 5930k which supports up to a maximum of 2133mhz ram speed. I am...
View ArticleRe: Cannot boot the board from SD card
just make sure the Galileo board firmware and the SD-Card Linux Image are the latest one.For my Galileo Gen 2 board, the firmware is version 1.0.4 and the SD-Card's image is SDCard1.0.4. (Notice the...
View ArticleRe: Error:Task 8 image-full-galileo.bb, do_rootfs
Hi JPMontero_Intel,There is nothing wrong with my new opencv-2.4.3.bb. The errors is:* satisfy_dependencies_for: Cannot satisfy the following dependencies for connman:* shadow-securetty **...
View ArticleDefault video memory address
Thinking a bit retro here, does the Intel Edison module provide us a default and accessible video memory address via the SOC. ie VGA memory from 0x000A0000 to 0x000BFFFF?
View Articlenfs on edison?
Does the supported Yocto image support nfs on Edison? if so, is there any examples to configure it?
View ArticleRe: Connecting Edison to WIFI
This is getting a little cumbersome and confusing. My /etc/wpa_supplicant/wpa_supplicant.conf file looks like this: ctrl_interface=/var/run/wpa_supplicantctrl_interface_group=0update_config=1ap_scan=1...
View ArticleRe: about atomisp
Hi,Thank you for your reply.And i need your help for another question.My platform: Intel Atom CPU E3827. Can you offered me the driver of ATOMISP MIPI-CSI2, and the corresponding firmware? Thank you...
View ArticleRe: CPU Power management on Yocto (edison-image) C-states
I also am very interested in this question. The default energy consumption of the Atom CPU on the Edison is pretty high and I wan't to see if I can better manage the battery life.
View ArticleClik here to view.
Re: Connecting Edison to WIFI
wpa_cli> select_network 0> enable_network 0> save> quitsystemctl enable wpa_supplicantbusybox udhcpc -i wlan0 if that doesn't completely solve it, you may have to re-edit your...
View Article